19.6 C
New York
Tuesday, May 28, 2024

How to Fix Car Ignition Lock Cylinder

The ignition lock is an essential part of any car and is located inside the lock body or assembly that’s usually welded on the steering column. In the majority of cases, when the problem occurs in the ignition system, the fault is due to the ignition lock cylinder. Sometimes, simple repairs solve the problem, but usually, the lock cylinder has to be replaced completely. The lock cylinder has a series of tumblers inside it where the key is inserted.

There is a series of switches as well that supply power to various other components. Due to a damaged or faulty ignition cylinder, sometimes the vehicle doesn’t start properly, and sometimes it does not get enough power to operate. Some of the reasons why the ignition lock cylinder requires repairs are discussed below, along with a detailed overview of how to repair it. 

When Do We Need Ignition Lock Cylinder Repairs?

Keys Don’t Turn in the Lock 

If the car key isn’t turning in the ignition lock, there can be a problem with the key. But in most cases, the problem lies inside the ignition cylinder. This is why locksmiths for ignition repair services in New Jersey focus on finding the problem first. It’s probably a worn or clogged wafer that doesn’t lift to the correct height when you insert the key. Aside from the issue of the water, there could be another internal sticking that may be preventing the car’s ignition cylinder from spinning. To allow ignition repair, the cylinder must remove and rotated.

The Car Doesn’t Start 

If there is an ignition problem and the car isn’t starting, troubleshooting can be a little more difficult as there can several other causes of that. If your car remote has a remote start function, test if the engine starts. If the problem persists, the ignition switch may be the problem; hence, the lock cylinder will require some necessary adjustments. You can also begin repairing your car’s ignition if the key feels loose or tight when you turn it. 

The Car Key Is Stuck Inside the Ignition

This can happen if the spring sticks or if debris builds up and the wafer does not have enough space to move. In some cases, the key may be the culprit, but repairing the car’s ignition is a simple solution to this problem. A stuck car key indicates that your ignition needs repair, but you’ll likely need a replacement rather than a repair.

Car Lock Cylinder Repairing Tools 

Though most of the locksmiths for ignition repair services in New Jersey suggest that a faulty lock cylinder should replace, simple repairs can still fix it. Although, the tools required to fix a damaged cylinder vary by vehicle. Usually, the tools required are 

  • Pickaxe
  • A pocket Screwdriver
  • Philips Screwdriver 
  • Repairing Manual
  • Safety Goggles

Steps to Fix an Ignition Lock Cylinder 

A professional locksmith can fix your car’s ignition cylinder lock. Though repairing ignition cylinders with locks is common, cars have now upgraded to electronic keys, which has made the process a bit difficult. A locksmith is a good option if you have problems with the type of lock or the device it works with. Although, a simple DIY procedure can also fix your ignition lock cylinder problem. Here is how

  1. Wear safety goggles for protection while working on the ignition lock.
  2. Open the car hood and disconnect the negative terminal from the battery. Keep it aside for some time.
  3. In some vehicles, removing the components that control the supplemental restraint system may be necessary when replacing the lock cylinder. It can get in the way, and the deployment of the airbags at any time can cause serious injuries. 
  4. There are shrouds or covers, commonly the steering column upper and lower shrouds, that block access to the lock cylinder. You must remove the screws that hold the cover together with a screwdriver.
  5. After that, remove the cover on the steering wheel to access the lock cylinder. 
  6. Insert the key inside the ignition cylinder to determine the problem. You can twist the key in the start position to see if the key gets stuck or not.
  7. Insert a small screwdriver in the lock barrel to loosen the lock barrel retention tab. 
  8. The lock barrel can remove by pulling it out of its covering. 
  9. Check the cylinder thoroughly to see if it’s broken or not. If it is broken from the inside, replacement of the cylinder will require. 
  10. However, if any kind of debris is stuck inside the cylinder, clear it and check if the key twists properly or not. 
  11. After fixing the problem, place the cylinder back and attach the negative terminal of the battery back to do a test run to see whether the car starts or not.
Jack henry
Jack henry
Hi, I'm admin of techfily.com if you need any post and any information then kindly contact us! Mail: techfily.com@gmail.com WhatsApp: +923233319956 Best Regards,

Related Articles

Stay Connected

0FansLike
3,912FollowersFollow
0SubscribersSubscribe

Latest Articles